The HEF4066B provides four single-pole, single-throw analog switch functions. Each switch has two input/output terminals (nY and nZ) and an active HIGH enable input (nE). When nE is LOW, the analog switch is turned off. The HEF4066B is pin compatible with the HEF4016B but exhibits a much lower ON resistance. The MAX4702 is a quad SPDT switch with one control input and one low-voltage digital logic power supply. These devices operate from a single +1.8V to +5.5V power supply. When powered from a +2.7V supply the MAX4699/MAX4701/MAX4702 offer a 75Ω on-resistance (R ON ), with 12Ω max R ON flatness and 4Ω max matching between channels. Product data sheet Rev. 04 — 19 December 2008 3 of 18 NXP Semiconductors 74HC1G66; 74HCT1G66 Single-pole single-throw analog switch 7. Functional description  H = HIGH voltage level; L = LOW voltage level. 8. Limiting values  The input and output voltage ratings may be exceeded if the input and output current ratings are observed. MICRO SWITCH MilitaryfiGrade Toggle Switches, TL Series TERMINAL CIRCUIT IDENTIFICATION Terminal identifications are referred to in the order guides to indicate which circuits are made in each toggle position (i.e., 1-2 refers to circuit closure through terminals 1 and 2). One Pole Two Pole Four Pole TERMINALS
Find many great new & used options and get the best deals for New Square D H321DS Safety Switch Disconnect 30 Amp 240v Fusible Stainless at the best online prices at eBay! Figure 8: Typical Wiring for DPST Switch (P72C, and D Models) Table 1: Single Pressure Controls Switch Action, Low Event, High Event, and Models Switch and Action Low Event High Event Models Single-Pole Single-Throw (SPST) Open-low Cut Out (Opens Line to M1) Cut In (Closes Line to M1) P70A, P70B, P170A Single-Pole Single-Throw (SPST) Open-high Single-Pole Double-Throw PIN Switch (PDT) Series PDT broadband double-throw (SPDT) PIN diode switches featuring Millitech technology is ideally suited for load switching, duplexers and receiver protectors in systems requiring state-of-the-art performance.
USB Switch ICs SPST Type (Single Pole Single Throw) BH6260MWX Description BH6260MWX is SPST x 2ch and Inverter x 2ch analog switches. Analog SW0 and SW1 pass USB 2.0 high-speed signal. Analog SW2 and SW3 pass UART signal. Moreover, this is guaranteed from 2.9V to 3.7V as for the range of the power-supply voltage. NC7SB3157P6X ON Semiconductor / Fairchild Analog Switch ICs Low Voltage UHS SPDT Analog Switch datasheet, inventory, & pricing. ... dual single-pole single-throw ... Buy DC Switch Momentary (ON)-OFF-(ON) Single Pole Double Throw Switch: Toggle Switches - Amazon.com FREE DELIVERY possible on eligible purchases
The NX3L1T384 is a low-ohmic single-pole single-throw analog switch. It has two input/output terminals (Yand Z) and an active LOW enable input pin (E ). When E is HIGH, the analog switch is turned off. Schmitt trigger action at the enable input (E ) makes the circuit tolerant to slower input rise and fall times.
The TS12A12511 is a bidirectional, single-channel, single-pole double-throw (SPDT) analog switch that can pass signals with swings of 0 to 12 V or –6 V to 6 V. This switch conducts equally well in both directions when it is on. The device also offers a low ON-state resistance of 5 Ω (typical), which is matched to within 1 Ω between channels. Eaton’s double-throw safety switches include two interlocked switches with a common connection used to transfer service from a normal power source to an alternate source, or to switch from one load circuit to another. The interlock ensures both switches cannot be closed at the same time, preventing them from being operated in parallel. ♦ +1.8V to +5.5V Single-Supply Operation ♦ Available in SOT23 Packages ♦ Fast Switching: tON = 50ns max, tOFF = 50ns max ♦ TTL-Logic Compatible (+5V Supply) ♦ Pin Compatible with MAX4544 ♦ Guaranteed Break-Before-Make (MAX4624) ♦ Guaranteed Make-Before-Break (MAX4625) MAX4624/MAX4625 1Ω, Low-Voltage, Single-Supply SPDT Analog ...
20 Amp, 120/277 Volt, Toggle Double-Throw Ctr-OFF Momentary Contact Single-Pole AC Quiet Switch, Industrial Grade, Grounding, Back & Side Wired, - Gray Leviton’s Industrial Grade AC toggle switches for extra heavy-duty applications represent top-of-the-line quality and peak performance.
Single-pole switches are the most common light switches in a home. They have two screw terminals plus a ground screw. One screw terminal is for the "hot" wire that feeds the switch from the power source. The other terminal is for a second hot wire, called a switch leg, that runs only between the switch and the light fixture.